MICREL KSZ8863 LINUX DRIVER

I am also trying to use KSZ switch in my board. Mentions Tags More Cancel. Ask a related question Ask a new question. The indemnities, obligations of confidentiality, and limitations on liability described in this Agreement, and any right of action for breach of this Agreement prior to termination, will survive any termination of this Agreement. I had that 4 days ago!! This would at least tell you if the problem is in the EMAC settings or not.

Uploader: Yohn
Date Added: 22 June 2005
File Size: 60.26 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 67373
Price: Free* [*Free Regsitration Required]

It seems the PIC32 Ethernet hardware takes control of the pins and never returns them. Licensee agrees that the linnux of this Agreement regarding unauthorized use and nondisclosure of the Software, Documentation, and related Proprietary Rights are necessary to protect the legitimate business interests of Microchip and its licensors and that monetary damage alone cannot adequately compensate Microchip or its licensors if these provisions are violated.

configuration examples for micrel ksz8863?

Why ksz88633 my PIC32 run slower than expected? Licensee, therefore, agrees that if Microchip alleges that Licensee or Third Party has breached or violated any provision in this Section then Microchip will have the right to injunctive relief, without the requirement for the posting of a bond, in addition to all other remedies at law or in equity.

Menu Search through millions of questions and answers User. The default for the KSZ seems mivrel support Spanning Tree Protocol which is most likely how we will leave the chip configured.

Looks like ksz device driver is never called while scanning kdz8863 phy. This thread has been locked. Mentions Tags More Cancel. Thanks in advance for the help. By checking the “I agree” box and clicking the “Confirm” button below: TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any micrle party intellectual property right.

  DOMEX DMX3191E DRIVER DOWNLOAD

I’ll take any embedded code for now. Mmicrel Agreement will constitute the entire agreement between the parties with respect to the subject matter of this Agreement. You must agree to the terms of each such applicable license, or you should not use the Open Source Components. The newly created question will be automatically linked to this question.

How did you configure internal register of KSZ? I’m not sure I would ever actually use it, but it would be nice to have. Thanks for the answer, Tommy. We are using same KSZ Leaving it floating was NOT correct.

Forum Themes Elegant Mobile.

configuration examples for micrel ksz? | Microchip

You may have run across my post, where I didn’t ground a pin. Microchip acquired Micrel around a year ago or so, so I expected there would be more documentation from them. The link is up, M full duplex. Hi aloha, We are using same KSZ If any provision of this Agreement will be miceel by a court of competent jurisdiction to be illegal, invalid, or unenforceable, that provision will be limited or eliminated to the minimum extent necessary so that this Agreement will otherwise remain in full force and effect and be enforceable.

May 29, 9: Low power consumption, advanced power management and sophisticated QoS features e.

  MATROX G200EV XP DRIVER DOWNLOAD

How to configure kszmll via SPI interface w | NXP Community

All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Lniux of this site. Licensee acknowledges that the foregoing limitations are reasonable and an essential part of this Agreement.

I tried to implement the SMI interface for the global and advanced registers, and I didn’t get that working, I only ever see 0’s coming back when I read any of the registers.

Ask a related question Ask a new question.

Do you have another question? Licensee may not remove or alter any copyright or other proprietary rights notice posted in any portion of the Software or Documentation and must include any proprietary notices on any copies of the Software or any derivatives thereof. Licensee will defend, indemnify, and hold Microchip and its subsidiaries harmless from and against any and all claims, costs, damages, expenses including reasonable attorney’s feesliabilities, and losses, including without limitation: Licensee agrees that the Software including but not limited to the Source Code, Object Code, and library files, if provided and its derivatives, Documentation and underlying inventions, algorithms, know-how and ideas relating to the Software and the Documentation are proprietary information belonging to Microchip and its licensors “Proprietary Information”.

VPN